Meaning of SURVEYING in English

SURVEYING

method of making relatively large-scale, accurate measurements of the Earth's surfaces. a means of making relatively large-scale, accurate measurements of the Earth's surfaces. It includes the determination of the measurement data, the reduction and interpretation of the data to usable form, and, conversely, the establishment of relative position and size according to given measurement requirements. Thus, surveying has two similar but opposite functions: (1) the determination of existing relative horizontal and vertical position, such as that used for the process of mapping, and (2) the establishment of marks to control construction or to indicate land boundaries. Surveying has been an essential element in the development of the human environment for so many centuries that its importance is often forgotten. It is an imperative requirement in the planning and execution of nearly every form of construction. Surveying was essential at the dawn of history, and some of the most significant scientific discoveries could never have been implemented were it not for the contribution of surveying. Its principal modern uses are in the fields of transportation, building, apportionment of land, and communications. Except for minor details of technique and the use of one or two minor hand-held instruments, surveying is much the same throughout the world. The methods are a reflection of the instruments, manufactured chiefly in Switzerland, Austria, Great Britain, the United States, Japan, and Germany. Instruments made in Japan are similar to those made in the West. Additional reading United States. Government Printing Office, Surveying and Mapping (1982), is a subject bibliography listing current sources. Informative introductory texts on surveying include William C. Wattles, Land Survey Descriptions, rev. ed., edited by Gurdon H. Wattles (1974); Charles A. Herubin, Principles of Surveying, 3rd ed. (1982); J.G. Olliver and J. Clendinning, Principles of Surveying: Plane Surveying, 4th ed. (1978); Jerry A. Nathanson and Philip Kissam, Surveying Practice, 4th ed. (1988); R.H. Dugdale, Surveying, 3rd ed. (1980); and Jack C. McCormac, Surveying Fundamentals (1983). Comprehensive treatments include Charles B. Breed and George L. Hosmer, The Principles and Practices of Surveying, 11th ed., rev. by W. Faig, 2 vol. (1977); Raymond E. Davis et al., Surveying, Theory and Practice, 6th ed. (1981); Russell C. Brinker and Paul R. Wolf, Elementary Surveying, 7th ed. (1984); Francis H. Moffitt and Harry Bouchard, Surveying, 7th ed. (1982); and G. Bomford, Geodesy, 4th ed. (1980). Instruments used in the practice are discussed in J. Clendinning and J.G. Olliver, Principles and Use of Surveying Instruments, 3rd ed. (1969, reissued 1972); and M.A.R. Cooper, Modern Theodolites and Levels, 2nd ed. (1982). Hydrography is the subject of A.E. Ingham (ed.), Sea Surveying, 2 vol. (1975); and Melvin J. Umbach, Hydrographic Manual, 4th ed. (1976). International Hydrographic Bureau, Hydrographic Dictionary , 3rd ed. (1970), contains useful information; and International Hydrographic Bulletin (monthly) and International Hydrographic Review (semiannual), published by the same organization, provide data on current research and developments. John Wilfrid Wright Modern surveying Basic control surveys Geodetic surveys involve such extensive areas that allowance must be made for the Earth's curvature. Baseline measurements for classical triangulation (the basic survey method that consists of accurately measuring a base line and computing other locations by angle measurement) are therefore reduced to sea-level length to start computations, and corrections are made for spherical excess in the angular determinations. Geodetic operations are classified into four orders, according to accuracy, the first-order surveys having the smallest permissible error. Primary triangulation is performed under rigid specifications to assure first-order accuracy. Efforts are now under way to extend and tie together existing continental networks by satellite triangulation so as to facilitate the adjustment of all major geodetic surveys into a single world datum and determine the size and shape of the Earth spheroid with much greater accuracy than heretofore obtained. At the same time, current national networks will be strengthened, while the remaining amount of work to be done may be somewhat reduced. Satellite triangulation became operational in the United States in 1963 with observations by Rebound A-13, launched that year, and some prior work using the Echo 1 and Echo 2 passive reflecting satellites. The first satellite specifically designed for geodetic work, Pageos 1, was launched in 1966. A first requirement for topographic mapping of a given area is an adequate pattern of horizontal and vertical control points, and an initial step is the assembly of all such existing information. This consists of descriptions of points for which positions (in terms of latitude and longitude) and elevations above mean sea level have been determined. They are occasionally located at some distance from the immediate project, in which case it is necessary to expand from the existing work. This is usually done on second- or third-order standards, depending upon the length of circuits involved. The accuracy of survey measurements can be improved almost indefinitely but only at increased cost. Accordingly, control surveys are used; these consist of a comparatively few accurate measurements that cover the area of the project and from which short, less accurate measurements are made to the objects to be located. The simplest form of horizontal control is the traverse, which consists of a series of marked stations connected by measured courses and the measured angles between them. When such a series of distances and angles returns to its point of beginning or begins and ends at stations of superior (more accurate) control, it can be checked and the small errors of measurement adjusted for mathematical consistency. By assuming or measuring a direction of one of the courses and rectangular coordinates of one of the stations, the rectangular coordinates of all the stations can be computed. Triangulation A system of triangles usually affords superior horizontal control. All of the angles and at least one side (the base) of the triangulation system are measured. Though several arrangements can be used, one of the best is the quadrangle or a chain of quadrangles. Each quadrangle, with its four sides and two diagonals, provides eight angles that are measured. To be geometrically consistent, the angles must satisfy three so-called angle equations and one side equation. That is to say the three angles of each triangle, which add to 180, must be of such sizes that computation through any set of adjacent triangles within the quadrangles will give the same values for any side. Ideally, the quadrangles should be parallelograms. If the system is connected with previously determined stations, the new system must fit the established measurements. When the survey encompasses an area large enough for the Earth's curvature to be a factor, an imaginary mathematical representation of the Earth must be employed as a reference surface. A level surface at mean sea level is considered to represent the Earth's size and shape, and this is called the geoid. Because of gravity anomalies, the geoid is irregular; however, it is very nearly the surface generated by an ellipse rotating on its minor axisi.e., an ellipsoid slightly flattened at the ends, or oblate. Such a figure is called a spheroid. Several have been computed by various authorities; the one usually used as a reference surface by English-speaking nations is (Alexander Ross) Clarke's Spheroid of 1866. This oblate spheroid has a polar diameter about 27 miles (43 kilometres) less than its diameter at the Equator. Because the directions of gravity converge toward the geoid, a length of the Earth's surface measured above the geoid must be reduced to its sea-level equivalenti.e., to that of the geoid. These lengths are assumed to be the distances, measured on the spheroid, between the extended lines of gravity down to the spheroid from the ends of the measured lengths on the actual surface of the Earth. The positions of the survey stations on the Earth's surface are given in spherical coordinates. Bench marks, or marked points on the Earth's surface, connected by precise leveling constitute the vertical controls of surveying. The elevations of bench marks are given in terms of their heights above a selected level surface called a datum. In large-level surveys the usual datum is the geoid. The elevation taken as zero for the reference datum is the height of mean sea level determined by a series of observations at various points along the seashore taken continuously for a period of 19 years or more. Because mean sea level is not quite the same as the geoid, probably because of ocean currents, in adjusting the level grid for the United States and Canada all heights determined for mean sea level have been held at zero elevation. Because the level surfaces, determined by leveling, are distorted slightly in the area toward the Earth's poles (because of the reduction in centrifugal force and the increase in the force of gravity at higher latitudes), the distances between the surfaces and the geoid do not exactly represent the surfaces' heights from the geoid. To correct these distortions, orthometric corrections must be applied to long lines of levels at high altitudes that have a northsouth trend. Trigonometric leveling often is necessary where accurate elevations are not available or when the elevations of inaccessible points must be determined. From two points of known position and elevation, the horizontal position of the unknown point is found by triangulation, and the vertical angles from the known points are measured. The differences in elevation from each of the known points to the unknown point can be computed trigonometrically. The National Ocean Service in recent years has hoped to increase the density of horizontal control to the extent that no location in the United States will be farther than 50 miles (80 kilometres) from a primary point, and advances anticipated in analytic phototriangulation suggest that the envisioned density of control may soon suffice insofar as topographic mapping is concerned. Existing densities of control in Britain and much of western Europe are already adequate for mapping and cadastral surveys.

Britannica English vocabulary.      Английский словарь Британика.